![]() | ![]() VIBRA-DRY® COMPOUNDS
Vibra-Dry polishing compounds for gemstones are convenient, time saving and re-usable. Vibra-Dry is formulated to be used absolutely dry, just as it comes from the container. It eliminates messy slurries, gels and fillers. It's clean to use - simply separate stones and compound in seconds by screening. Replace compound in it's original container for the next usage. You save time, labor and compound. Vibra-Dry compounds are formulated for pre-polishing and final polishing only. All material must be pre-finished through #600 Silicon Carbide grit before using Vibra-Dry. Gem materials below 6+ on the MOH scale of hardness usually require a special pre-polish in aluminum oxide pre-polish prior to finishing with dry polishing methods. If material is not properly prepared before using Vibra-Dry, results may not be satisfactory. Vibra-Dry is not recommended for use in rotary or barrel type tumblers. ( 3 to 7.5 MOH scale) Soft to Medium hard Materials, USE GRITS 600 - 2500 - 25000. ( 8 to 8.5 MOH scale) Hard Materials, USE GRITS 1700 - 14000
New formula is environmentally friendly. Extender relubricates STANDARD Vibra-Dry compounds and extends their life so they can be re-used longer. Order # 402-10-02-99 -- 4 oz -- us$7.50 Use with burnishing media for acieving bright finishes on jewelry metals. Great on both silver and gold. Starting ratio is a heaping tablespoon to a gallon of water. Adjust as necessary. Order # 400-BC-20 -- Net Weight - 1 lb - Shipping Weight - 1 lb 4 oz -- us$4.90 Fillers are an important addition to the stone/grit mix in almost any tumbling sequence or tumbler. Fillers help distribute the grit to the stone or metal part, and act as a cushion between the parts. Steel shot and ceramic bits are commonly used with metal while the softer fillers and plastic pellets are better for stone. Ground walnut shells treated with red rouge make an excellent final polish for metals including silver, gold, brass, etc. Keeps items separated and aids in the tumbling process. Packaged in 1 lb and 5 lb bags. Order # 400-WSR-1 -- Net Weight - 1 lb w/rouge - Shipping Weight - 1 lb 4 oz -- us$3.00 Order # 400-WSR-5 -- Net Weight - 5 lb w/rouge - Shipping Weight - 5 lb 4 oz -- us$12.50 Makes a good filler for tumbling gemstones. Keeps stones from hitting one another during the tumbling process. Order # 400-WS-1 -- Net Weight - 1 lb Plain - Shipping Weight - 1 lb 4 oz -- us$2.50 Order # 400-WS-5 -- Net Weight - 5 lb Plain - Shipping Weight - 5 lb 4 oz -- us$9.50 Use as a filler when polishing stones or metals. Clean to use. Packaged in 1 lb and 5 lb. bags. Order # 400-PP-1 -- Net Weight - 1 lb - Shipping Weight - 1 lb 4 oz -- us$2.00 Order # 400-PP-5 -- Net Weight - 5 lb - Shipping Weight - 5 lb 4 oz -- us$7.50 Ground corn cobs. Makes an excellent filler for polishing stones. Softer than Walnut shells. Comes in 1 lb and 5 lb bags. Order # 400-CC-1 -- Net Weight - 1 lb - Shipping Weight - 1 lb 4 oz -- us$4.00 Order # 400-CC-5 -- Net Weight - 5 lb - Shipping Weight - 5 lb 4 oz -- us$17.50 Non-abrasive, angle cut cylinders. Used as a burnishing media on jewelry metals. Approximately 24 hr. break-in. Also used as a filler and carrier in tumbler loads of stone. Really speeds the job and helps leave a super finish. Cylinder size approx. 5/32 x 5/16 inch. Order # 400-CM-15 -- Net Weight - 1 lb - Shipping Weight - 1 lb 4 oz -- us$5.00 Use as a burnishing media for metals. Contains a mixture of balls, ball-cones and angle cut cylinders that are the right shape and size for jewelry work. No pins. Stainless steel shot will not rust. Use with burnishing compound. Order # 400-SS-10 -- Net Weight - 1 lb - Shipping Weight - 1 lb 4 oz -- us$18.25
DEALERS WANTED WORLD WIDE !
Inquire Here
Your Internet Email Address:
![]()
|